 Western blot stripping problem |
  |
  Jan 26 2005, 09:44 AM
Post
#1
|
|
|
member  Group: Active Members Posts: 6 Joined: 6-December 04 From: UFSC, Brazil Member No.: 4995  |
Hi! I have stained with sucess a protein with 27 KDa, but when I tried use the membrane again to stain other protein, I observed the last bands.
How can I remove Ab 1st stained from my membranes? I have ised strip with NaOH 0.1M. Thanks |
 |
 
|
|
Jan 26 2005, 10:31 AM
Post
#2
|
|
|
Enthusiast Group: Active Members Posts: 95 Joined: 13-December 04 From: Barcelona Member No.: 5058 |
You can try 62.5 mM Tris pH 6.8, 2% SDS and 100 mM 2-mercaptoethanol. Incubate the membrane at 50ºC for 30 min with ocassional agitation and then wash with TBST and block again.
-------------------- Science is a wonderful thing if one does not have to earn one's living at it
(A.Einstein) |
|
|
|
|
Jan 28 2005, 10:04 AM
Post
#3
|
|
|
member Group: Active Members Posts: 6 Joined: 28-January 05 Member No.: 5498 |
5 min H2O
5-10 min 0.2 H NaOH 5 min H2O Works good. |
|
|
|
|
Mar 31 2005, 05:30 AM
Post
#4
|
|
|
member Group: Members Posts: 3 Joined: 31-March 05 Member No.: 6359 |
Hi all,
Usually, after I do the 1st stripping, all most proteins in the membrane disappeared ( I checked it by staining that membrane with Ponceau solution) or just remained a little.  The contents of stripping buffer I used is: + 0.2 M Glycine (pH 2.5) + 0.05% Tween 20 I incubated the membrane at 80oC for 30 minutes. And then, I washed it 10 min x 3 times with TBST before blocking with skim milk. What's wrong in my method and how can I solve the problem? Thank you! 
This post has been edited by Gin: Mar 31 2005, 05:37 AM |
|
|
|
|
Mar 31 2005, 06:21 AM
Post
#5
|
|
|
Veteran Group: Active Members Posts: 291 Joined: 15-April 04 From: Bordeaux - France Member No.: 2987 |
hi
i start to see same problems as you and i use the same protocol of stripping. Hence i'm wondering is "our" glycine too old? mine is more than 3 month... but for stripping protocol, there was a discussion here from protein and proteomics forum fred |
|
|
|
|
Mar 31 2005, 06:48 AM
Post
#6
|
|
|
member Group: Members Posts: 3 Joined: 31-March 05 Member No.: 6359 |
QUOTE (fred_33 @ Apr 1 2005, 12:21 AM) hi i start to see same problems as you and i use the same protocol of stripping. Hence i'm wondering is "our" glycine too old? mine is more than 3 month... Hi Fred, Thanks for your reply. Well, but I don't think so. Because another person who taught me that method, he also used the same Glycine with me. And of course, no matter  Thus, I considered the pH of buffer, or the incubate-temperature, or the shaking... are they important to the result of stripping?When you had that problem, how can you overcome it, Fred? You changed with "new" glycine? Gin, |
|
|
|
|
Mar 31 2005, 07:58 AM
Post
#7
|
|
|
Veteran Group: Active Members Posts: 291 Joined: 15-April 04 From: Bordeaux - France Member No.: 2987 |
hi
i think ph is not that important caus i use pH 2.7 at 80°C for 30' but the two last stripping were not by shaking i must admit, and the residual bands apperead just in the pas times. hence i assume that shaking would increase efficiency |
|
|
|
|
|
Lo-Fi Version | Time is now: 21 Nov 2009 - 05:03 PM |
| IP.Board Skin Developed By Creative Networks | ||
|
Home
- About
- Terms of Service
- Privacy
- Feedback
©1999-2009 Protocol Online, All rights reserved. |