Jump to content

  • Log in with Facebook Log in with Twitter Log in with Windows Live Log In with Google      Sign In   
  • Create Account

Submit your paper to J Biol Methods today!
- - - - -

Treating Hep G2 with drugs

  • Please log in to reply
3 replies to this topic

#1 shs



  • Active Members
  • Pip
  • 19 posts

Posted 14 April 2009 - 09:18 PM

I am planing to treat Hep G2 with different kinds of drugs(EtOH, paracetamol, phenobarbitone, WY14643, cisplatin and doxorubicin).
My question is what is the proper way to prepare the drugs. I have read in some articles that a stock of drug can be prepared in DMSO which can be stored in -20C and then a serial dilution by using media can be used to prepare the final concentrations---in other articles they prepare the drugs directly by dissolving the drug in media.....so I got CONFUSED <_<
Should the media used for preparation of drugs contain FBS??
Any protocole for preparing the drugs will be great :wacko:

Any help....in details plzzzzzzzzzzzz
Science is What We Need To Understan The Life

#2 cotchy



  • Active Members
  • PipPipPipPipPip
  • 87 posts

Posted 15 April 2009 - 12:52 AM

The reason some people dissolve their chemical in DMSO is that the particular chemical they are using is not water soluble, therefore they must use a solvent to dissolve the drug first.

If you need to dissolve in DMSO you must reduce the level of DMSO down to 0.01 % of the total volume of the media to make sure that this is not causing toxicity to your cells (DMSO can be toxic to cells at a higher concentration than 0.01%)

Also add a control set of wells to your experiment containing the highest concentration of DMSO only (i.e. 0.01%, if this is your highest conc.) This allows you to observe the effects that this conc of DMSO is having on your cells without the additon of the selected drugs.

To reduce the level of DMSO down to 0.01% for non water soluble drugs:

Dissolve a pre-selected amount of drug in DMSO (you should normally find solubility range on the drugs MSDS)

1)Perform a 1:100 (10 ul with 990 ul media) dilution of your stock with your media to get a 1% DMSO solution (this can contain FCS if you are only looking at cell viabilty/death as an end point

If you are looking at another end point you may need to remove the FCS if you think the factors it contains may have an effect on the results.

However you could also perform another set control set of wells with no FCS to see if their is a difference in your results

2)Perform another 1:100 dilution of your 1% drug/DMSO solution with your media, again with or without FCS if you need it,

This will give you your 0.01% drug/DMSO stock,

The actual concentration of your chemical in the DMSO depends on on how concentrated it was at the start as it will now be a 1:10,000 dilution of this as you performed two 1:100 dilutions,

So if you started with a 100mg chemical in 1 ml DMSO (100mg/ml stock), your highest working conc is 100mg/10,000 = 0.01 mg/ml or 10ug/ml. This is your new stock.

3)You can then use this stock to make up all your other dilutions using just your media

For water soluble drugs perform dilution exactly the same way but remove the DMSO at start and just dissolve in your normal media


Edited by cotchy, 15 April 2009 - 12:58 AM.

#3 bob1


    Thelymitra pulchella

  • Global Moderators
  • PipPipPipPipPipPipPipPipPipPip
  • 6,507 posts

Posted 15 April 2009 - 04:34 PM

Cisplatin is much more soluble and stable in Dimethyl formamide (DMF) than in DMSO.

#4 shs



  • Active Members
  • Pip
  • 19 posts

Posted 15 April 2009 - 06:42 PM

Thank you soooooooooooooooooooooooooo much is not enough to express my appriciation..........

Thank you again and again................ :( :) :) :) :) :) :) :) :) :)
Science is What We Need To Understan The Life

Home - About - Terms of Service - Privacy - Contact Us

©1999-2013 Protocol Online, All rights reserved.