This is a cached page for the URL ( To see the most recent version of this page, please click here.
Protocol Online is not affiliated with the authors of this page nor responsible for its content.
About Cache
Polymerase III in vitro Transcription (Hahn Lab)

Polymerase III in vitro Transcription

Steve Hahn

last modified 10/15/99

For the following reactions, use appropriate shielding and dispose of radioactive waste properly!


A 20 microliter transcription reaction contains:

4.0 ul 5X Pol III transcription buffer

0.2 ul 0.1 M DTT

0.2 ul alpha amanatin (1 mg/ml)

0.2 ul RNAse Inhibitor (Amersham, 20 U)

2.0 ul NTP stock

0.5 ul alpha 32P GTP

140 ng plasmid template (pSK LEU3, pCH6), [use 280 ng 5S pUC template]

H2O to 20 microliters final volume.

Transcription Protocol:

For a Typical transcription reaction, make an NTP mix containing:

2.0 ul NTP stock

0.5 ul alpha 32P GTP

DNA template

H20 to a final volume of 3 microliters


Make a second mix containing all other transcription components except protein:

4.0 ul 5X Pol III transcription buffer

0.2 ul 0.1 M DTT

0.2 ul alpha amanatin (1 mg/ml)

0.2 ul RNAse Inhibitor

H20 to a final volume of 16 microliters less the maximum volume of protein to be added.


Aliquot the second mix to all reaction tubes and incubate on ice.


Add the protein extract (typically 20-40 micrograms of a whole cell extract) and any other proteins to be added. Add extract dialysis buffer (or protein dilution buffer) to bring all reactions to the same volume.

Add 3 ul of the NTP mix to each reaction, mix by flicking the tube 5-6 times, and immediately incubate at 30 degrees (the reactions will work well between room temp and 32 degrees).

After 30 min., stop the reaction with 180 microliters stop solution.

Extract once with phenol/CHCl3 (2/1). ETOH precipitate with 20 ul 3M NaOAc and 600 ul ETOH.

Freeze 10 min. Spin 10 min. Remove sup. with a drawn out pasteur pipette. Add 200 ul 100% ETOH and spin 3 min. Remove sup. again.

Dry pellets but do not overdry. Thoroughly resuspend pellets in Formamide dye solution containing 0.1% SDS.

Heat 1 min. 90 degrees and put on ice. Load to 0.4 mm thick urea acrylamide gel (don’t forget to clean the wells of the gel just before loading). Typically, run 300V, 60 min until the bromphenyl blue is 3/4 of the way to the bottom.

Dry gel 20-30 min. Typically expose ~3 hr or overnight without a screen.

Solutions needed for Pol III transcription:


5X Pol III Buffer (store frozen) (1 ml):

10% glycerol 200 ul 50% glycerol
100 mM HEPES, 7.9 100 ul 1M HEPES
400 mM KCl 400 ul 1M KCl
25 mM MgCl2 25 ul 1 M MgCl2
5 mM EDTA 20 ul 0.25 M EDTA
  255 ul H20


NTP Stock (store frozen —70 deg):

5 mM each ATP, CTP, UTP

0.5 mM GTP


7.3 ml Stop mix (make fresh):

0.1 M NaOAc 250 ul 3M NaOAc
10 mM EDTA 300 ul 0.25 M EDTA
  6.4 ml H20
0.5% SDS 375 ul 10% SDS
5 ug/ml tRNA 1.2 ul tRNA (30 ug/ml)



Extract Dialysis Buffer (store frozen —70 deg):

20 mM HEPES, 7.9

100 mM KCl

5 mM MgCl2


20% glycerol

2 mM DTT


Protein dilution buffer (5 ml) store -70 deg:

20 mM Tris 8.0 100 ul 1 M Tris 8.0
1 mM DTT 50 ul 0.1 M DTT
10% glycerol 1 ml 50% glycerol
150 mM KCl 0.75 ml 1 M KCl
1 mM EDTA 20 ul 0.25 M EDTA
50 ug/ml BSA 2.5 ul 100 mg/ml BSA
H2O to 5 ml total volume



20 ml Acrylamide Urea Gel:

3 ml 40/2% sequencing acrylamide

2 ml 10X TBE

8.5 g Urea

8 ml H20

microwave ~10 sec and stir to dissolve.


Add 175 ul 10% ammonium persulfate

Remove 1 ml acrylamide and add 1 ul TEMED. Pour plug at bottom of gel. Let polymerize a few minutes.

To the remaining acrylamide, add 18 microliters TEMED and pour gel. Gel can stored O/N, if kept wet and sealed at room temp.


Back to Hahn Lab Methods Index