This is a cached page for the URL (http://stanxterm.aecom.yu.edu/wiki/index.php?page=Quick_colony_screening). To see the most recent version of this page, please click here.
Protocol Online is not affiliated with the authors of this page nor responsible for its content.
About Cache
Pamela Stanley lab wiki - Quick colony screening
November 1, 2009 | Home | What is Wiki | Adding or editing content | All documents | Disclaimer | Pamela Stanley Lab
Recently viewed: Home> Quick colony screening
Document: Quick colony screening | Last modified: December 07, 2005
Quick Screening Of Colonies For Plasmid With Insert
SP, Dec 05

After transformation of bacteria and overnight growth of antibiotic-resistant colonies, one often needs to identify the colonies containing the DNA of interest (usually, plasmid DNA with an insert). In certain cases where a high success-rate is expected (such as after ligation of a small insert into a vector using sticky-ends created using two different restriction enzymes), only a few colonies can be picked and plasmid DNA prepared from all using Qiagen plasmid mini-prep columns, etc.

However, in cases where a lower efficiency of right ligation is expected (such as in case of blunt-end cloning), one may need to screen many colonies. Kit based methods can become cost or effort-intensive. The following three are alternate and cheap methods in such cases.

PCR-based screening

Pick up colonies with a 200 ul pipette-tip - the colony will stick - then dispense into tubes containing 50-200 ul culture medium (with the selection agent, antibiotic) and pipet 3-4 times to resuspend the colonies.

Alternately, you can grow picked-up colonies overnight in 2-3 ml culture medium.

Set up PCR reactions (25 ul volume, 25-30 cycles) using 1 ul of bacteria. The primers can be insert-specific or both against insert as well as the vector (e.g., a T7 primer can be used; T7 sites are on many plasmids next to the cloning sites) - in case of latter, one can infer the orientation of the insert.

Electrophorese PCR products.

Restriction enzyme digestion-based screening

Direct lysis buffer

2 mg/ml lysozyme and 0.2 mg/ml RNase A in 15% sucrose (w/v), 10 mM Tris at pH 8, 1mM EDTA and 0.1 mg/ml BSA.

For 10 ml of 1x stock, use 100 ul of 1 M Tris, 200 ul of 0.5 M EDTA, 1.5 g sucrose, 20 mg lysozyme, 100 ul of 20 mg/ml RNase A and 100 ul of 10 mg/ml BSA.

This can be done with either overnight cultures or colony resuspensions described above. Use 1 ml of overnight culture (pellet the bacteria) or as much as possible of the colony resuspension (colonies should be 0.5 mm or larger in size and resuspended in 20 ul; unless the colony is large - like 2 mm - leave the mini-culture suspensions at 37 deg for 2-4 h).

Resuspend in 50 ul of 1x stock (if using overnight culture) or 20 ul of 2x stock (with 20 ul of colony resuspension; remember to leave some for future cultures) of 'direct lysis buffer' and vortex.

Boil for exactly 90 secs.

Spin down at high speed (12k-20k g) at RT for 10 min and collect supernatant.

Use all or 10-20% (in case of overnight cultures) for restriction enzyme digestion, electrophoresing all of the reaction at end.

Plasmid DNA migration-based screening

This is based on the principle that a plasmid containing an insert will be longer in size and thus migrate faster (being more super-coiled) than a plasmid without one. This principle is not applicable to cases where the insert is small relative to the vector (thus not making a discernible difference to the plasmid's migration). A method is described here - Cracking gel method.
∑ accuracy, clarity, cost, ease, logic | 327930 wiki pages served since 2.20.05 | Admin login | Disclaimer